2013 Volkswagen Jetta: How to Remove a Door Panel in 60 Seconds

How to Remove the Door Panel on a 2013 Volkswagen Jetta

This guide will show you how to remove the door panel on a 2013 Volkswagen Jetta. The door panel is held in place by a series of clips, so it is important to be careful when removing it so that you don’t damage the clips.

Steps

1. Open the door and remove the door armrest.
2. Remove the Phillips head screws that hold the door panel in place.
3. Pry the door panel away from the door using a plastic trim tool.
4. Disconnect the wiring harnesses and remove the door panel.

Tools

Phillips head screwdriver
Plastic trim tool

So, 2013 Volkswagen Jetta How To Remove Door Panel?

To remove the door panel on a 2013 Volkswagen Jetta, you will need to:

1. Remove the plastic trim piece at the bottom of the door by prying it up with a flathead screwdriver.
2. Remove the two Torx T25 screws that hold the door panel in place.
3. Pull the door panel up and away from the door.
4. Disconnect the wiring harnesses for the door lock, window switch, and power mirror.
5. Remove the door panel.

2013 Volkswagen Jetta How to Remove Door Panel

Tools Needed

Torx T20 screwdriver
Small flathead screwdriver
Plastic trim removal tool

Step 1: Remove the door panel trim

1. Starting at the bottom of the door panel, use a small flathead screwdriver to pry up the trim piece.
2. Once the trim piece is loose, use your fingers to pull it off of the door panel.
3. Repeat steps 1 and 2 for all of the trim pieces around the door panel.

Step 2: Remove the door panel screws

1. Use a Torx T20 screwdriver to remove the screws that hold the door panel in place.
2. There are usually two screws located at the top of the door panel, and two screws located at the bottom of the door panel.

Step 3: Remove the door panel

1. Carefully pull the door panel away from the door.
2. There may be some clips that need to be released, but they should be easy to find.
3. Once the door panel is free, set it aside.

Step 4: Replace the door panel

1. To reinstall the door panel, simply reverse the steps above.
2. Make sure that all of the clips are properly engaged before you tighten the screws.

Tips

Be careful not to damage the door panel when you are removing it.
If you are having trouble removing the door panel, you can try using a heat gun to soften the adhesive.
Always replace the door panel screws after you have removed them.

MUST READ THIS: How To Remove Volkswagen Jetta Headlight

FAQs: 2013 Volkswagen Jetta How to Remove Door Panel

How do I remove the door panel on a 2013 Volkswagen Jetta?

1. Locate the door panel removal clips: There are three clips located on the top of the door panel, one on each side of the door handle.
2. Insert a flathead screwdriver into the slot of each clip and pry up until the clip pops out:
3. Repeat steps 1 and 2 for the remaining clips:
4. Gently pull the door panel away from the door until it is free:
5. Disconnect the wiring harness from the door panel:
6. Remove the door panel:

What tools do I need to remove the door panel on a 2013 Volkswagen Jetta?

You will need a flathead screwdriver to remove the door panel clips.

How long does it take to remove the door panel on a 2013 Volkswagen Jetta?

It should take about 10 minutes to remove the door panel on a 2013 Volkswagen Jetta.

What are the risks of removing the door panel on a 2013 Volkswagen Jetta?

There are a few risks associated with removing the door panel on a 2013 Volkswagen Jetta. These include:

Damaging the door panel or the clips that hold it in place.
Accidentally disconnecting the wiring harness.
Causing the door to not close properly.

Is it difficult to remove the door panel on a 2013 Volkswagen Jetta?

No, it is not difficult to remove the door panel on a 2013 Volkswagen Jetta. However, it is important to be careful not to damage the door panel or the clips that hold it in place.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *